Deep Reflections Hardwood Floors Co. Refinishing
There’s no Job too big or too small for us to take on. Call Now for Free Quote 214 553 1577
Dust Free Sanding
We use the top professional methods and procedures when it comes to Dust Free Sanding process.
Hardwood Stain
Choose from a wide variety of colors of stain for hardwood floors.
Hardwood Floor Finishes
Hardwood Flooring finishes should be done by a professional.
We use only the best hardwood floor finishes on the market.
Dust Free Sanding
Hardwood Floor Refinishing Process
Dust Free control is an important factor when it comes to hardwood flooring refinishing. At Deep Reflections Hardwood Floors we use dust control systems that will keep your home clean during the sanding process. Dust has chemicals and It can get on any kind of surface, which can be unhealthy if inhaled. We use modern as well as the most efficient industry HEPA certified dust control systems. This will eliminate 99.9% of dust and prevents it from spreading. With our experience, we are very well aware of the dangers that dust can cause. To protect the health of our employees and our customers, we always make sure the proper dust containment methods are used during every job that we perform. We make sure that proper floor preparation is completed before the refinishing begins. We will also determine If repair is needed prior to the new finish being applied. Our Certified professionals will first sand your floors to remove all scratches. All proper dust containment methods will be used to ensure a clean and safe environment while the refinishing is completed. Deep Reflections Hardwood Floors is without a doubt, your best choice for professional hardwood floor installation and refinishing service.
Important Note: Hardwood flooring is often coated in chemical protective layers, which will be removed during the refinishing process. In older houses, these may contain harmful chemicals. Make sure that the environment is properly ventilated before you begin, and wear protective breathing gear and goggles to protect yourself throughout the entire process.
After you vacuum, wipe the entire floor surface with a tack cloth, a wax-impregnated piece of cheesecloth designed to pick up and hold dust residue. Plan to use several tack cloths — don’t overextend the cloths’ dust-holding capacity.
Varnish: Varnish comes in a variety of lusters, from matte to glossy. The higher the gloss, the more durable the surface. Varnish often darkens with age. On the up side, you can make spot-repairs to varnish.
Many professional floor refinishers use equipment with heavy-duty dust removal attachments that help keep your house from getting messy.
Note that hardwood floors which have been waxed or cleaned with an oil soap can’t be abraded unless you first remove all of the residue. Otherwise, you’ll get a blotchy finish. Use mineral spirits or a wax remover to take off any old wax or oil soap before beginning.
Once the wood is sanded down it will be completely vulnerable to stains, damage, gouges, and scratches. That means that you need to apply a treatment that can help to protect it from further damage, so you can maintain the brand-new look of the surface for as long as possible. Some products can also enhance the appearance of the flooring itself.
Using 180-grit sandpaper, hand-sand the perimeter of the room and any nooks that the buffer can’t reach. Rub with the grain 4 to 6 inches out from the baseboard, working over each board until the finish dulls and a powder forms. Don’t use a sanding block for refinishing hardwood—it might miss uneven spots in the floor.
Safety Tip: Store and dispose of oil-soaked rags properly. The heat generated naturally from wood oils on rags can set the rags on fire, especially if they are bunched together or in a closed container. Hang the rags outside, away from any structures, and allow them to dry thoroughly before disposing of them.
Tip: Eliminating scratches and stains are among the necessities of wood floor refinishing. Sanding can remove scratches from wear and tear but it’s no match for a deep gouge or chip in the hardwood flooring. Sanding can sometimes remove a stain caused by water but staining from pet urine produces dark discoloration deep within the flooring often, these often does not disappear with sanding. These boards will need to be replaced.
Hardwood floor refinishing is dusty and noisy. Always wear a good dust mask or respirator, ear protection, and goggles. Seal doorways off doorways with plastic sheeting and turn off forced-air HVAC to keep dust from circulating throughout your house.
You are removing dirt and old stain and creating a new level surface, so choose the initial sandpaper accordingly. Remember the smaller the grit number, the rougher the sandpaper and the more material it will remove. Start with a coarse grit and move to finer grits as the floor begins to get smoother with each sanding. Sanding grit estimates vary according to the condition of your floor. In general, begin with a 20 to 60 grit and end with 120. You may choose to skip the 20 grit pass if the floor is relatively smooth. Always use the same grit progression on all areas, whether drum, edge or hand sanding. Remember to clean the floor thoroughly after each sanding grit change.
Pour out a 4-inch-wide stripe of finish in line with the grain—only as much as you can spread in 10 minutes. Using a long-handled roller with a ¼-inch nap cover, roll out the finish with the grain, then across it. Overlap each pass and work quickly to keep a wet edge. After 10 minutes, brush more finish along the edge, then pour and roll again for 10 minutes. Continue until the floor is covered. Wait 3 hours before recoating and a week before putting back furniture.
All of these products should be applied according to the manufacturer’s instructions and need to be brushed on in very thin, even lines. Allowing the finish to bubble, pool, or sit in standing areas can cause permanent damage to the material.
Dust Free control is an important factor when it comes to hardwood flooring refinishing. At Deep Reflections Hardwood Floors we use dust control systems that will keep your home clean during the installation and sanding processes. Dust has chemicals and It can get on any kind of surface, which can be unhealthy if inhaled. We use modern as well as the most efficient industry certified dust control systems. This will eliminate 99.9% of dust and prevents it from spreading. We are experienced and well aware of the dangers that dust can cause. To protect the health of our employees and our customers, we always make sure the proper dust containment methods are used during every job that we perform. We make sure that proper floor preparation is completed before the refinishing begins. We will also determine If repair is needed prior to the new finish being applied. Our professionals will first sand your floors to remove all scratches. All proper dust containment methods will be used to ensure a clean and safe environment while the refinishing is completed. Deep Reflections Hardwood Floors is undoubtedly your best choice for professional hardwood floor installation and refinishing service.
Professional Hardwood Floor Refinishing
Professional Hardwood Floor Refinishing Near Me
To begin the process of removing the damaged surface layer, use a large walk-behind sander, which can be pushed over the floor using a slow, even pace, to gently grind the wood down to a level that is below any finish treatments or damage. These machines are large and difficult to direct, and it is very important that you employ them in an even motion so that you do not get uneven surfaces, dips, or rises in the installation. The attached vacuum should suck up most of the dust that is generated.
Ideally, you want to seal the floor on the same day you finish sanding to prevent the open wood surface from absorbing moisture. For best results, apply the stain (if desired) and sealer with a lambs wool applicator. Be sure to apply the sealer evenly, and use enough to cover the surface. But be careful not to apply too much. Excess sealer doesn’t soak into the wood — it pools on the surface. If you fail to remove it, it leaves an ugly, ugly spot.
Large machines will not be able to fit in corners or small spaces, so small hand guided to refinish these areas. While much lighter and easier to maneuver, these can be tricky as you have more control and can make more mistakes. Again, try to practice in areas that will not be highly visible in the finished space, so you can get used to this equipment.
Professional Hardwood Floor Refinishing
The vacuums and Dust Extractors which we use in your home are HEPA certified combined with attachments included, even our most power sanders will extract and contain the dust generated by the sanding and refinishing process. However, it is still important to vacuum the room thoroughly before proceeding.
The vacuum attachments included in most power sanders will suck up the majority of the sawdust generated by the refinishing process. However, it is still important to sweep and/or vacuum the room thoroughly before proceeding.
Staining any of the hardwood flooring is optional, but applying a finish is essential to protect any wood’s surface. Without a finish, wood can dry, split and deteriorate. If exposed to moisture, It would swell due to which drawers and doors would no longer work. A perfect finish prevents swelling and cracking, protects against stains and enhances the appearance of your floor.
Staining the floor: After completing the sanding process, and complexly remove any dirt, it is time to stain the wood floor. This process depends on the color you choose for your floor, and the conditions. It may require more than one layer, to get to the desired result.
How To Refinish A Hardwood Floor
Everyone likes hardwood flooring for its unique characteristics; the patterns in the wood grain and the natural color of the wood does absolutely make a subtle statement about the look and feel of your home. Staining your hardwood floor can add another dimension to the overall look of your floors.
What You Need To Know About Hardwood Floor Refinishing
Polyurethane: Either oil- or water-based, polyurethane comes in various degrees of luster and has a sort of plastic look. Oil based sealer will darken and yellow the stain color of the hardwood, however Bona water-based sealer is clear and will always stay clear and will not darken the stain color of the hardwood floors. When it comes to finish, we will use Bona products in most cases but the other brands which we can use don’t darken as much as oil. Bona finishes are excellent for high-traffic and high-moisture areas. However, if the finish gets nicked or gouged, it’s extremely difficult to spot-repair.
Hardwood Floor Refinishing Color Ideas
Penetrating sealer: This offers a natural-looking finish that brings out the wood’s grain; however, it may darken over time. Penetrating sealer offers good protection, especially when waxed. However, it’s less durable than polyurethane or varnish. It’s the easiest of the three to spot-repair, though.
If you perform the work yourself, then you will have to rent a walk-behind, solid-wood sanding machine as well as hand sanding tools. Mistakes can also be made, which can irreparably damage the wood flooring surface, requiring costly repairs or a complete reinstallation.
You’ll need to rent a floor buffing tool with a series of screen grits to restore the luster to your floor’s topcoat. A buffing tool is much less aggressive than a drum sander and easier to use. Sweep and vacuum up any dust between each grit.
Sanding the wood floor: Sanding is a process of removing the upper layer of wood floor, to smooth the floor, and prepare for the next part. This process requires many preparations, to make sure it will include as less dust and dirt as possible, and Deep Reflections Hardwood Floors is one of the top companies in or around Dallas, Plano, Frisco, McKinney, Prosper, Celina, Allen, Fairview, Lucas, Coppell, Flower Mound and many other areas that ensures that the refinishing process will go as smooth and as clean as humanly possible.
Leave the room for 10 to 15 minutes to let the powder settle. Put a clean filter in the vacuum, and sweep the floor using a felt-bottomed attachment. Work in line with the flooring strips, then sweep across them to get any powder that settled between the boards. Finally, dry-tack the floor with a microfiber cloth pushed with the grain.
Cover your shoes with booties and your nose and mouth with a respirator that has organic vapor canisters. Strain the finish through a cone filter into a clean plastic watering can, minus a sprinkler head, then pour some strained finish into a small plastic container. Brush a 3-inch-wide stripe beside the baseboards at a point farthest from your exit door. You’ll have lap marks if the edge of the stripe starts to dry, so stop after 10 minutes and go to the next step.
What You Need To Know About Hardwood Floor Refinishing
How To Refinish Hardwood Floors
After you’ve completed all the sanding, you must remove all the dust from the floor, molding, and walls. Wipe down the walls and moldings once to get the dust onto the floor, and then use a damp rag on the moldings to remove any residue. You don’t want any dust falling onto the floor later, when the new finish is drying. Let the dust settle (72 hours) and then vacuum. A standard shop vacuum with a dust filter will do the trick.
Hardwood Floor Refinishing Color Ideas
Penetrating sealer: This offers a natural-looking finish that brings out the wood’s grain; however, it may darken over time. Penetrating sealer offers good protection, especially when waxed. However, it’s less durable than polyurethane or varnish. It’s the easiest of the three to spot-repair, though.
Safety Tip: Store and dispose of oil-soaked rags properly. The heat generated naturally from wood oils on rags can set the rags on fire, especially if they are bunched together or in a closed container. Hang the rags outside, away from any structures, and allow them to dry thoroughly before disposing of them.
Tip: Eliminating scratches and stains are among the necessities of wood floor refinishing. Sanding can remove scratches from wear and tear but it’s no match for a deep gouge or chip in the hardwood flooring. Sanding can often remove a stain caused by water but staining from pet urine produces dark discoloration deep within the flooring that often does not improve with sanding.